Inflatable Tent Advantages

1: What is an inflatable tent

Inflatable tent is a kind of tent design framework using the principle of structural mechanics, the use of gas pressure characteristics of the air bag expansion to form a certain rigid column, through the organic combination to support the skeleton of the tent. It is mainly used for moisture-proof, water-proof, wind-proof, dust-proof, sun-proof, rescue and disaster relief, short-term field training and short-term field combat.

1) Fabric material :PVC coated cloth 2) inflatable column material :PVC coated polyester woven cloth

3) Suitable temperature :-30°-+70°4) Frame wind resistance :6-8

5) Hydrostatic pressure ≥16kpa6) Surface water :160-200mm

7) Inflating time :2-10min(varies with tent size)

Desert camouflage inflatable tent

2: The characteristics of inflatable tent

1) Process

Using adhesive bonding and high frequency thermal bonding technology production, the air column is made of PVC double-sided coating cloth, tarpaulin is made of waterproof, anti-ultraviolet material, with fast forming, high strength, fire, mildew, anti-ultraviolet, moisture-proof and other advantages. The tent is an inflatable tent, and the tent frame is an air column structure. Compared with the general metal bracket tent, it has the characteristics of light body, small volume after folding, convenient and easy to carry.

2) Assembly and erection

Inflatable tent erection is very convenient, first choose a ground level place, and then open the package, the inflatable tent flat on the ground, with an air pump or foot pump began to inflate, four corners stand a person (such as the tent area is small 1-2 people can also be completed), pull the rope to prevent the focus can not balance up, until it is held up. Finally, anchor the ground and tighten the wind rope.

3) Demolition

When the inflatable tent is removed, it only needs to be naturally deflated, or pumped by an electric charge and exhaust pump.

4) Advantages

Compared with the ordinary metal bracket tent, the inflatable tent has its incomparable advantages, its light weight, small size, in the transportation of the ordinary metal bracket tent has no advantages. And its erection and removal are very simple, will not waste more manpower and time, especially suitable for the rapid response of emergency. Inflatable tents can also be air-dropped when conditions are too bad to reach.

5) Performance

Set up and disassembly is relatively simple and fast, you can install or disassemble in a very short time, to save your precious time; Better insulation, inflatable tent using high quality pvc waterproof canvas, tear resistance, better tensile strength, better aging resistance, long service life.

High pressure inflatable tent

6) The difference between inflatable tent and ordinary metal support tent

1-- Weight

The metal bracket tent uses iron pipe as the bracket, so its weight is relatively large, which inevitably brings trouble to the transportation and movement. In particular, the larger the area of the tent, the more support is used, and with the increase of the tent area, the bearing demand is greater, which results in the increase of the weight of the support, the corresponding wall thickness of the iron pipe will be used, the weight of the tent is greater. Inflatable tents, with inflatable keels that can be folded, are lighter in weight and easier to transport than ordinary metal tents with iron pipe supports.

2-- Volume

The same in the tent volume, the metal bracket structure of the tent, due to the existence of iron pipe bracket, can not be freely packed; And the length of the iron pipe support is generally longer, resulting in a slightly smaller vehicle will not be put in, so that in its transportation, it must use relatively large vehicles. The inflatable tent, because it is soft, inflatable keel, and the air column can be folded freely after being deflated; This design makes the tent after use, can be freely folded, only occupies a small volume, can easily fit into small household vehicles and ordinary vehicles. Easy to transport.

A military inflatable camping tent

3-- Erection and removal

The metal tent needs more people to set up, the erection time is long, and the bigger the tent, the more personnel need, the longer the time.

7) Installation precautions

1. When installing on mud or sand, you can dig drains around the tent to ensure that the inside of the tent is dry.

2, if you need to cook in the tent, be sure to keep the flame away from the tarpaulin or fire plate isolation flame, cooking people can not leave the tent, usually do a good fire plan, and install exhaust fan to exclude soot.

3. If the local wind is predicted to exceed force 8, please remove the tent in advance. So as not to cause unnecessary losses.

4, cotton tent storage before be sure to dry tarpaulin, to be recovered after folding storage, such as too late to cool dry tarpaulin, remember that must not be long, so as not to mildew.

5, according to the local humidity and climate conditions, regularly dry tarpaulin, so as not to breed bacteria, the disaster relief tent rain coating is destroyed.

8) Inflatable tent maintenance

If you notice a leak, you can first wipe the column clean and then apply soapy water to the surface to check for the leak. If the leak point is a very small hole, you can use a small piece of circular maintenance cloth (any specification of inflatable tent standard distribution inside all), and then brush the glue, glue to dry after sticking on the leak point, firmly bonded.

Inflatable tent processing workshop

If the leak is unglued at the hot joint of the air column, it can be handled by the following steps:

1. Clean the bonding surface first.

2, we will give the inflatable tent dispensing glue, inflatable tent air column special glue, brush it on the pre-bonded surface, must be coated evenly, the thickness is appropriate, brush the picture two times, you can glue.

3. The shape of the adhesive interface shall be designed as round or oval, and the shape of square and acute Angle interface shall be avoided as far as possible. The lap width shall not be less than 30mm.

4. After the glue evaporates, it can be bonded. The patch must be flat, without folds, rolled and scraped, and the hair dryer is used to supply heat source for easy bonding. After 6 hours of bonding, it can be inflated and used.